Saturday, November 14, 2026

Woodworking Tip of the Day: Clamp Pressure: Snug, Not Strangled — How Much Squeeze a Glue Joint Really Needs

This is catching the MOAM's attention today….. how hard to crank the clamps. Walk into any shop from Gloucester to the Cape and you'll see two kinds of glue-ups. One guy leans on every handle like he's trying to close a stuck storm door. The other guy gives it a polite little twist and hopes for the best. Both of them are guessing. You don't have to. The glue makers publish the numbers, and the math takes about a minute on the back of a scrap.

Why it matters: Clamp pressure squeezes the glue into a thin, continuous film, pulls the faces into full contact and holds everything still while it sets. Too little and the joint never closes. Way too much on a small glue area and you crush the wood and push the glue out. For yellow PVA glue, Titebond's own spec is "enough to bring joints tightly together," which works out to about 100 to 150 psi for softwoods, 125 to 175 psi for medium woods and 175 to 250 psi for hardwoods. The USDA Wood Handbook says the same thing in government-speak: about 100 psi for low-density wood, up to about 250 psi for the densest stuff.

Materials

  • PVA wood glue (Titebond Original, II or III) for shop and interior work
  • Epoxy, wood flour or other thickening filler for the boat (more on that below)
  • Cauls and wax paper or packing tape so the cauls don't get glued on
  • A damp rag or a scraper for the squeeze-out

Tools

  • Enough clamps. Pipe clamps, parallel clamps, bar clamps, whatever you've got, but count them first
  • Tape measure and a pencil for the math
  • A couple of bench risers so you can clamp over and under the work

Steps

  1. Dry fit first. A good joint should close with light pressure. If you need a ton of force to pull a gap shut, fix the joint. Don't count on the clamps. PVA isn't a gap filler, and the Wood Handbook says most wood glues don't fill gaps well.
  2. Figure the glue-line area. That's the area of the faces getting glued, not the face of the board. Edge-gluing two 3/4-in. boards, 36 in. long: 3/4 × 36 = 27 sq in.
  3. Multiply by the psi for your wood. White pine at 100 to 150 psi needs 2,700 to 4,050 lb total. White oak at 175 to 250 psi needs 4,725 to 6,750 lb. That's a lot more than most folks think.
  4. Divide by what your clamps can do. A Pony #50 3/4-in. pipe clamp is rated at 1,200 lb. A BESSEY K Body REVO parallel clamp is rated at a nominal 1,700 lb, a BESSEY TGC clutch-style bar clamp up to 700 lb, and a BESSEY EZS one-hand clamp at a nominal 445 lb. So that oak joint wants 4 to 6 pipe clamps, 3 to 4 parallel clamps, or 11 to 16 of the one-handers. Those ratings are best case. When WOOD Magazine tested one-handed bar clamps, they only got into the softwood range or a bit under it. Treat your count as the minimum.
  5. Space them so the pressure overlaps. Fine Woodworking's rule of thumb is that clamp pressure spreads in about a 45° cone from each jaw, so it reaches along the glue line about as far as the jaw sits from it. Alternate clamps over and under so the panel doesn't bow. (Spacing and cauls got their own tips back in September and October.)
  6. Spread an even coat and clamp from the middle out. Bring each clamp up snug, then go back around. With big pipe and parallel clamps, snug is the word. You don't need to hang off the handle.
  7. Read the squeeze-out. What you want is a small, continuous bead along the whole joint. That tells you there's enough glue and the joint is closed. If the bead has dry skips, you're short on glue or the clamps are too far apart. That's your "starved" joint. If you see big puddles, you used too much glue, not too much pressure.
  8. Then hands off. Titebond says to keep an unstressed joint clamped 30 minutes to an hour, and 24 hours for a stressed joint. Don't put stress on it for 24 hours.

The "starved joint" business: Everybody's heard you can starve a joint by over-clamping. With PVA and hand clamps on a full-length edge joint, that's mostly a myth. Fine Woodworking tested it and found that tight joints didn't starve. The professor they worked with said most woodworkers actually under-clamp. Where it gets real is a big clamp on a small glue area. Put one 1,700-lb parallel clamp on a 3/4 × 2-in. joint (1.5 sq in) and you're over 1,100 psi, more than four times Titebond's top number. That's how you crush fibers and squeeze the glue away. WOOD Magazine's advice fits: with the heavy clamps, don't go past snug.

Epoxy plays by different rules. On the Chamberlain dory, anything below the waterline gets epoxy, not Titebond. Titebond III's own spec says it's not for continuous submersion or below the waterline. WEST SYSTEM's guidance is the opposite of "crank it." Use only enough clamping pressure to hold the parts in place and squeeze a small amount of thickened epoxy out of the joint. Don't squeeze it all out. That's how you get a resin-starved epoxy joint. Wet out both faces with plain mixed epoxy first, then put on epoxy thickened just enough to bridge any gaps. When you're bedding hardware, tighten the fasteners until epoxy squeezes out, and stop there.

MOAM's shop note: Do the math before the glue comes out, not after. If the numbers say you need eight clamps and you own five, you'll find out halfway through a ten-minute open time with glue on your elbows. Count them, lay them out, set them to width and dry-run the whole thing. And one for the boat shop: never treat epoxy like yellow glue. The guy who cranks a scarf or a stem lamination down until nothing comes out has just built himself a dry joint.

Snug, not strangled. Let the glue do the work.

MOAM Out.

Sources: Titebond Original, II, III and Speed Set technical data (titebond.com); Titebond FAQs; USDA Forest Products Laboratory, Wood Handbook, Chapter 10; Fine Woodworking, "How Strong Is Your Glue?" and the Roman Rabiej clamping series; WOOD Magazine, "Take it easy with clamping pressure"; Woodcraft, "Goof-Proof Clamping"; Pony Jorgensen pipe clamp fixture specs; BESSEY Woodworking Solutions 2023-2024; WEST SYSTEM User Manual and Handy Pack instructions.

New Real Estate Listings on the North Shore Today – Saturday, November 14

New Listings Today – North Shore 29 Towns

This is catching the MOAM's attention today….. 18 new listings hit the market over the last 24 hours, across 9 North Shore towns.

Top towns: Lynn with 5, Marblehead with 4, then Salisbury and Beverly with 2 each.

By property type: Residential Lease (rentals) 10 · Residential 7 · Commercial Lease 1.

The MOAM's take: rentals outnumbered homes for sale today, and Lynn and Marblehead made up half of the new inventory.

Contact Nanepashemet to view these.
Nanepashemet Real Estate Services
Call or text 781-727-6516
jnestor@nanepashemet.com

MOAM Out.

Listing data courtesy of MLS Property Information Network (MLS PIN); listings shown are held by various brokerages. Nanepashemet Real Estate Services, MA Broker Lic. 136995-RE-B.

Boston Sports Morning Report — Saturday, Nov. 14

Not for nuthin'…. But….. it's a big Saturday in Boston: the Bruins are back at the Garden tonight looking to shake off that Montreal clunker, and Sunday brings Patriots football from Munich plus the Celtics at home. Here's your Saturday board.

New England Patriots

  • Yesterday: No game (lost 45-27 to Green Bay last Sunday)
  • Today: No game
  • Next: Sun., Nov. 15, 9:30 AM ET, @ Detroit Lions (in Munich, Germany; Lions are the designated home team)
  • Standings: 5-4, 2nd in the AFC East, 2.5 games behind Buffalo (7-1), currently the No. 7 seed in the AFC

Still holding the last AFC playoff spot. Set the alarm, because that kickoff comes early.

Boston Red Sox

  • Yesterday / Today: No games, it's the offseason
  • Next: Opening Day, Thu., March 25, 2027, @ Seattle Mariners (start time to be announced; home opener at Fenway is Thu., April 1 vs. Cincinnati)
  • Final 2026 record: 87-75, 3rd in the AL East

Hot stove season. Pitchers and catchers can't come soon enough.

Boston Celtics

  • Yesterday: No game (won 98-93 @ Toronto on Wednesday)
  • Today: No game
  • Next: Sun., Nov. 15, 6:00 PM ET, vs. Dallas Mavericks (TD Garden)
  • Standings: 10-2, 1st in the Atlantic (a half game ahead of Philadelphia, 10-3), No. 1 seed in the East, 5-game winning streak

Five straight and a couple days off. Dallas comes to the Garden Sunday evening.

Boston Bruins

  • Yesterday: No game (lost 5-2 to Montreal on Thursday)
  • Today: Sat., Nov. 14, 7:00 PM ET, vs. Minnesota Wild (TD Garden)
  • Next: Tue., Nov. 17, 7:00 PM ET, vs. Los Angeles Kings (TD Garden)
  • Standings: 13-5-1, 27 points, 3rd in the Atlantic, one point behind Tampa Bay and Montreal (28 each)

Minnesota is atop the Central at 14-3-4, so it's a good test for a bounce-back night at the Garden.

That's the Saturday board. Enjoy the weekend, Boston.

MOAM Out.

New England This Morning — November 14, 2026

Not for nuthin'…. But….. Saturday morning and New England can't agree on a season. The sun is breaking through a sky full of mackerel clouds over Marblehead Harbor, Mount Washington's camera is buried in rime with snow showers on the way, and the Mad River covered bridge sits under a gray sky waiting on rain and snow showers. Here's how three corners of New England looked around 7:40 this Saturday morning.

Marblehead Harbor (BYC Oceanfront) — A low sun glowing through rippled clouds, gold light spilling across the water, empty moorings, and the Neck's houses catching the morning. Mostly sunny with a high near 46 and a northwest wind around 9 mph. A fine morning for a walk along the water.

Mount Washington, NH (Observatory North View) — Rime ice packed across the lens again, so it's all frost and no view. Snow showers likely with around an inch possible, a high near 20, northwest winds 15 to 30 mph gusting to 40, and wind chills as low as 7 below. Winter has the summit.

Mad River Valley, VT (Great Eddy Covered Bridge) — The old covered bridge in Waitsfield with the flag out front, a still river reflecting the farmhouse, rusty brush and bare trees, and the hills under low cloud. Cloudy with rain and snow showers and a high near 40. Mud boots and a warm hat.

The Bartlett Experimental Forest camera still hasn't updated since Thursday afternoon, so it sits this one out again.

Webcam views courtesy of the Boston Yacht Club, the Mount Washington Observatory and Mad River Valley Television.

MOAM Out.

Friday, November 13, 2026

Woodworking Tip of the Day: Roll and Tip an Epoxy Barrier Coat: Three Thin Coats, Tacky to Tacky

Roll and Tip an Epoxy Barrier Coat

Not for nuthin'…. But….. the best epoxy coat on a boat is the one you never have to sand between. I've got the dory's bottom panels ready for coating, and this is the part where a lot of guys get impatient. They slop on one fat coat with a brush, get runs, sags and a surface like an orange peel. Then they spend the weekend sanding it back off. There's a better way, and the WEST SYSTEM folks spell it right out: thin coats with a foam roller, tipped off, one on top of the next while it's still tacky.

Why it matters: A barrier coat is there to keep water out of the wood and give the paint or varnish a smooth, stable base. WEST says a minimum of two coats makes an effective moisture barrier, and three if you're going to sand it, which they recommend for most wooden boats. One coat rolled on with their thin foam roller and tipped off at room temperature (70°F) comes out around 3 to 4 mils thick. Two coats gets you 6 to 7 mils, good for most exterior surfaces. For a hull bottom that sits in the water, 9 to 10 mils is the minimum. The trick is putting coat two on while coat one is still tacky. That way the coats bond chemically, and you skip the wash-and-sand in between.

Materials

  • Epoxy resin and hardener, metered with the pumps (pick the hardener for your shop temperature)
  • Thin urethane foam roller covers (WEST 800 or similar), plus one to cut up for tipping
  • Nitrile gloves, mixing pots and stir sticks
  • For the final prep: clean water, Scotch-Brite pads, paper towels and 80-grit paper

Tools

  • A roller frame and a plastic roller pan
  • A mini roller frame for the cut-down tipping brush
  • A utility knife or bandsaw for cutting the roller cover
  • A thermometer in the shop
  • Respirator and good ventilation if the shop is closed up (see yesterday's tip)
Epoxy barrier coat plan diagram

Steps

  1. Finish everything else first. All the fairing and glass work should be done before the final coating starts. Prep the surface the way you would for bonding: clean, dry and sanded.
  2. Let the wood settle at temperature. If cold wood is warming up while you coat it, the air in the wood expands and comes out through the epoxy as bubbles. WEST calls that out-gassing. In a New England shop in November, bring the panels in and give them time to stabilize before you start.
  3. Make a tipping brush. Cut a thin foam roller cover into short segments and put one on a mini frame. WEST suggests exactly that. They say foam brushes are generally too flexible for this.
  4. Mix small and pour it out. Mix only what you can spread during its open time, and pour it into the roller pan as soon as it's mixed. Spread out in a thin layer, it stays workable longer than it does in the cup.
  5. Load the roller light. Moderate load, then roll the excess off on the ramp of the pan so the cover is evenly wet.
  6. Roll a 2 ft × 2 ft patch. Roll lightly and randomly to move the epoxy onto the area. As the roller dries out, press a little harder and spread it into a thin, even film. Thinner is better. Thin coats don't run or sag. Finish with long, light strokes and overlap the last patch to blend.
  7. Tip it off after each batch. Drag the tipping brush lightly across the fresh epoxy in long, even, overlapping strokes. Use enough pressure to knock down the stipple, but not so much that you pull the coat off.
  8. Swap the tip direction every coat. WEST's pattern is first coat vertical, second horizontal, third vertical, and so on.
  9. Recoat while it's tacky. Put the next coat on when the last one is tacky, like masking tape, but firm enough to hold the weight of the new coat. WEST says that window runs anywhere from 15 minutes to several hours, depending on the hardener and the temperature. To skip sanding between coats, get them all on the same day.
  10. Prep for paint or varnish. Let the final coat cure overnight. Then wash it with clean water and a Scotch-Brite pad to get the amine blush off, dry it with paper towels, and sand it before the finish goes on.

MOAM's shop note: If you come back and it's gone hard and you can't dent it with a thumbnail, you've missed the window. Don't roll another coat on and hope. Don't wipe it with acetone either. Blush is water soluble, so wash it with water and a Scotch-Brite, dry it, and sand any glossy spots dull with 80 grit. Then coat. When you're not sure whether it's gone too far, WEST says to play it safe: let it cure all the way, then wash and sand. And one more trick for the cold months: never thin epoxy with solvent to make it roll easier. Warm the resin and hardener up instead, and pick the right hardener for the temperature.

Three thin coats, tacky to tacky, done by suppertime. Your sanding block will thank you.

MOAM Out.

Sources: WEST SYSTEM, "Barrier Coating" and "Epoxy Chemistry" (westsystem.com); WEST SYSTEM User Manual (2020 US and 2025 EU editions); "Amine Blush & Cured Epoxy," WEST SYSTEM; "The Basics of WEST SYSTEM Epoxy Resin and Hardener," Epoxyworks.

New Real Estate Listings on the North Shore Today – Friday, November 13

New Listings Today – North Shore 29 Towns


Not for nuthin'…. But….. 29 new listings hit the market over the last 24 hours, across 14 North Shore towns.

Top towns: Peabody, Gloucester and Middleton with 4 each, then Salem, Danvers, Saugus, Merrimac, Lynn and Swampscott with 2 each.

By property type: Residential 15 · Residential Lease (rentals) 8 · Commercial Lease 3 · Residential Income 1 · Land 1 · Business Opportunity 1.

The MOAM's take: a three-way tie at the top today, and homes for sale were about half of the new inventory.

Contact Nanepashemet to view these.
Nanepashemet Real Estate Services
Call or text 781-727-6516
jnestor@nanepashemet.com

MOAM Out.

Listing data courtesy of MLS Property Information Network (MLS PIN); listings shown are held by various brokerages. Nanepashemet Real Estate Services, MA Broker Lic. 136995-RE-B.

Boston Sports Morning Report — Friday, Nov. 13

Not for nuthin'…. But….. the Bruins' four-game win streak ran into a buzzsaw named Montreal last night, and the whole Boston board is quiet today before a big weekend. Here's your Friday board.

New England Patriots

  • Yesterday: No game (lost 45-27 to Green Bay on Sunday)
  • Today: No game
  • Next: Sun., Nov. 15, 9:30 AM ET, @ Detroit Lions (in Munich, Germany; Lions are the designated home team)
  • Standings: 5-4, 2nd in the AFC East, 2.5 games behind Buffalo (7-1), currently the No. 7 seed in the AFC

Still holding the last AFC playoff spot. Wheels up for Munich and an early-morning kickoff.

Boston Red Sox

  • Yesterday / Today: No games, it's the offseason
  • Next: Opening Day, Thu., March 25, 2027, @ Seattle Mariners (start time to be announced; home opener at Fenway is Thu., April 1 vs. Cincinnati)
  • Final 2026 record: 87-75, 3rd in the AL East, out in the Wild Card round vs. the Yankees

Hot stove season. Pitchers and catchers can't come soon enough.

Boston Celtics

  • Yesterday: No game (won 98-93 @ Toronto on Wednesday)
  • Today: No game
  • Next: Sun., Nov. 15, 6:00 PM ET, vs. Dallas Mavericks (TD Garden)
  • Standings: 10-2, 1st in the Atlantic (a half game ahead of Philadelphia, 10-3), No. 1 seed in the East, 5-game winning streak

Five straight and a day off. Home for Dallas on Sunday.

Boston Bruins

  • Yesterday: Lost 5-2 vs. Montreal Canadiens (Casey Mittelstadt scored both Boston goals)
  • Today: No game
  • Next: Sat., Nov. 14, 7:00 PM ET, vs. Minnesota Wild (TD Garden)
  • Standings: 13-5-1, 27 points, 3rd in the Atlantic, one point behind Tampa Bay and Montreal (28 each)

The Habs jumped out to a 5-0 lead and the win streak ended at four. Time to bounce back against the Wild on Saturday.

That's the Friday board. Enjoy the weekend, Boston.

MOAM Out.

Sutton's $16 Billion Kraft Data Center, and a 2028 Ballot Fight Over Your Electric Bill

Not for nuthin'…. But….. Tuesday night, residents in Sutton packed a Select Board meeting to push back on a $16 billion data center campus from the Kraft Group. Today that fight got bigger. A committee just launched a 2028 statewide ballot question that would require a two-thirds vote in the host town — and a promise that the costs don't get shifted onto everyone else's electric bill (WBUR).

What's on the table in Sutton

The Kraft Group is pursuing a data center campus in Sutton, a Central Massachusetts town of about 9,700 people, about 10 miles south of Worcester (Boston Globe). If the project is completed, it would rank as the fourth-largest data center in the country (WBUR; the Globe attributes that ranking to the research firm Cleanview).

As town officials laid it out this week, the plan is 10 buildings on land owned by Unified Global Packaging Group, near the Millbury line. At full build-out it would draw about 900 megawatts, enough to power a sizable city. The first two buildings, about 250,000 square feet each, are aimed at 2029, with two more added each year through 2033 (Boston.com; Globe).

No application has been filed. The Select Board took no vote. It was the first public airing of the plan, and all six residents who spoke during public comment said no (Boston.com).

The tax pitch is real

Town Manager Austin Cyganiewicz estimated the first two buildings would pay about $10.4 million a year in property taxes starting in fiscal 2031, rising to about $27.8 million a year by 2035. He said that would lower the tax bill of an average single-family home, assessed at $662,000, by about $2,300 in 2031 (Boston.com). Sutton's entire tax levy for fiscal 2027 is about $32 million (CBS Boston). That's a lot of money for a small town staring at a budget deficit of about $350,000 (Boston.com).

For a board looking at that math, a $16 billion campus looks like a way out. Residents still weren't sold. They cited power, water, noise and what a project that runs around the clock would do to a town that still thinks of itself as rural. Michael Galli put the identity question this way: "I don't want to see this town sell its soul and get stuck as kind of the dumping ground of the AI industry." Select Board Chair Jonathan Anderson said he has "a really strong dose of skepticism and concern about this project," and warned against letting a budget deficit drive the decision (Boston.com).

The other bill is the one on your electric statement

New England already pays some of the highest electric rates in the country. A customer that large does not just "show up" on the grid. Somebody pays for the wires, the substations and the new supply. If that somebody is the developer, fine. If it isn't, the tab shows up on electric bills across Massachusetts — including here on the North Shore.

Gov. Maura Healey's executive order, signed September 8, is supposed to speak to that. It generally covers data centers over 25 megawatts. It calls for community benefit agreements and municipal guidance, and it requires developers to procure new clean electricity rather than just pulling from what the rest of us already use. The town's approval is a precondition for state permits, and the developer is supposed to pay for grid upgrades (WBUR; Boston.com). On paper, that's the right idea.

The question is whether it holds when the campus actually plugs in. The order does not require a town-wide vote. And like any executive order, a future governor can amend it or revoke it (WBUR).

A 2028 ballot question aimed at that gap

That's the gap a new statewide campaign is trying to close. The Committee to Restrict Data Centers, which filed paperwork with the state in September, announced the campaign Thursday and launched sign4restrictingdatacenters.org, where residents can pledge support. Attorney General Andrea Campbell's office has already certified the proposal (WBUR).

Under that petition, a data center could not get a municipal permit unless two big conditions were met. First, residents in the host town would have to approve it by a two-thirds vote. Second, its electricity supplier would have to agree not to shift costs onto other customers, and commit to providing enough electricity from 100% renewable resources to meet the facility's needs without reducing the renewable power available to everyone else. Operators would also have to guarantee recovery of infrastructure costs if a facility closes, shrinks, or breaks its contract. Water suppliers would have to certify that existing systems can handle it without hurting service in the host town or neighboring communities (WBUR).

The committee is aiming for the 2028 statewide ballot, not a rush this month. That gives organizers time to build support, and it puts the Legislature on notice when a new session starts in January. The committee's chair, Jim Fleming, said that if lawmakers pass a real law — "not just an executive order" — they may wrap the whole process. Sen. John Velis, a Westfield Democrat, is also promoting the campaign, citing electricity costs, water use, noise and environmental uncertainty (WBUR).

The petition would go further than the governor's order. It would cover facilities down to 5 megawatts of peak annual demand, not 25. And unlike the order, it would require that community-wide vote (WBUR).

Local control, and a regional bill

Look, the tax windfall in Sutton is not imaginary, and neither is the other side of the ledger. A small town should get to decide what kind of place it wants to be. That's local control, and that's how it should be. But a 900-megawatt neighbor does not stop at the Sutton town line. If the protections hold, the developer and its supplier pay for the power and the upgrades. If they slip, the cost lands on the rest of us — the same people already paying too much to keep the lights on.

A two-thirds vote, and a written promise that the costs don't get dumped on everyone else's electric bill, is a pretty straightforward test. Let the people who have to live next to it decide. And don't stick the rest of Massachusetts with the tab.

What do you think? Should a project this size need a two-thirds vote in the host town, and a guarantee that your electric bill doesn't pick up the slack? Tell me in the comments.

MOAM Out.


Sources: WBUR / State House News Service, Nov. 13, 2026 · Boston.com, Nov. 11, 2026 · Boston Globe, Nov. 10, 2026 · Boston Globe, Nov. 11, 2026 · CBS Boston, Nov. 10, 2026

New England This Morning — November 13, 2026

Not for nuthin'…. But….. Friday the 13th and New England's playing it gray. A soft pewter sky hangs over a still Marblehead Harbor with a few showers still around, Mount Washington's camera is locked in rime with wind chills below zero, and the Mad River covered bridge sits quiet under a cloudy late-fall sky. Here's how three corners of New England looked around 7:40 this Friday morning.

Marblehead Harbor (BYC Oceanfront) — A flat gray sky with just a hint of pink, glassy water dotted with empty moorings, and a lone gull crossing toward the far shore. Rain likely before noon, mostly cloudy with a high near 43 and a north wind 8 to 15 mph, gusting to 33. Keep the umbrella handy this morning.

Mount Washington, NH (Observatory North View) — Rime ice caked across the lens again, so the view is all frost and no mountain. Mostly cloudy with a high near 21, northwest winds 20 to 35 mph gusting to 45, and wind chills as low as 3 below. Not a day to be on the summit.

Mad River Valley, VT (Great Eddy Covered Bridge) — The old covered bridge in Waitsfield with the flag out front, a calm river mirroring the farmhouses, rusty brush and bare trees, and the hills soft under the clouds. Mostly cloudy with a high near 42 and a light north wind. A good morning for coffee by the window.

The Bartlett Experimental Forest camera hadn't updated since yesterday afternoon, so it sits this one out.

Webcam views courtesy of the Boston Yacht Club, the Mount Washington Observatory and Mad River Valley Television.

MOAM Out.

Thursday, November 12, 2026

Woodworking Tip of the Day: Winter Shop Air: Ventilating for Epoxy and Solvents in the Cold

Wicked cold out there this week, and the shop doors are shut….. The heater's humming, the dory's on the strongback, and I'm about to wipe her down with acetone before the next coat of epoxy. That's exactly when a winter shop turns on you. In July the big doors are open and the air takes care of itself. In November everything you put in the air stays in the air, right there with you and that heater.

Why it matters: A closed-up shop is a box. Solvent and epoxy vapor build up in it. WEST SYSTEM says plainly that vapors can build up in unvented spaces, and they want ample ventilation or an organic vapor respirator. Acetone, the stuff we all wipe with, has a flash point of 0°F per NIOSH. Its vapor is heavier than air and can travel along the floor to a flame across the room. Then there's the heater itself. An unvented kerosene or propane torpedo heater puts carbon monoxide into the room, and it adds moisture and CO2 too. Those feed amine blush on your fresh epoxy. So the same heater can light the vapor, gas you, and wreck your coat. Let's fix all three.

Materials

  • Disposable nitrile gloves (neoprene, butyl or natural rubber also work per WEST). Plenty of them
  • NIOSH-approved organic vapor (OV) cartridges, black label. If you'll be sanding too, use combination OV/P100 cartridges, black and magenta (3M 60921 is one)
  • A zip-top bag or sealed container for the respirator between uses
  • Foil-backed rigid foam insulation, tape, and a light bulb or heating pad for a warm box
  • Your solvents, with the lids kept on

Tools

  • A window or box fan you can set in a window blowing out
  • A half-face respirator that fits your face
  • A battery-operated CO alarm
  • A thermometer in the shop, and one in the warm box
  • For heat while the epoxy cures: an electric heater with a thermostat and a tip-over shutoff

Steps

  1. Heat the shop first, then shut the flame heater off. Bring the shop, the boat and your materials up to temperature with whatever you've got. Then, before any thinner, acetone or solvent finish comes out, turn off every heater with an open flame or a glowing element and let it cool. Jeff Jewitt makes the same point in Fine Woodworking: stoves and heaters with an open flame or glowing element are a hazard around flammable finishes. Propane construction heater makers agree. One DESA manual says to keep the area clear of gasoline, paint thinner and other flammable vapors.
  2. Set up cross-ventilation, not a stir fan. Put the fan in a window near the work, blowing out. Crack a window or door on the far side for make-up air. Then stand so the fresh air comes past you first, across the work, and out the fan. A fan in the middle of a closed shop just stirs the vapor around and into your face. Jewitt's rule for hand-applied finishes is a fan rated in cfm about equal to the room's volume (length x width x height). A 16 x 24 shop with 8 ft ceilings is 3,072 cubic feet, so look for about 3,100 cfm. He's clear that it only works if you give the replacement air a way in, and that it isn't enough for spraying.
  3. Put on your gloves and respirator, and check the seal. Every time you put the respirator on, do the negative-pressure check from OSHA's appendix. Palms over the cartridges, breathe in gently so the mask pulls in, and hold it ten seconds. If it stays pulled in with no leak, you're sealed. Then do the positive check: cover the exhalation valve and breathe out gently. You should feel a little pressure and no air leaking at the edges. Skin is the bigger exposure with epoxy, though. WEST says skin contact is the most common way people get exposed to resin and hardener, and sensitization can come after many exposures or just one. Glenn House, Gougeon's product safety director, says a typical 4 to 6 mil disposable lasts about 30 minutes with epoxy, so change them before then, and double-glove on long jobs.
  4. Wipe or brush, then purge. Do the solvent wipe or the epoxy coat. Keep lids on the cans and get solvent rags out of the shop. Let the fan run until the smell is gone. Then close up and heat again. That's Jewitt's winter routine too: apply, vent, then close up and reheat for drying.
  5. Keep the epoxy warm instead of the whole shop. Build a box from foil-backed rigid insulation with a light bulb or heating pad inside. WEST says to keep resin and hardener at 70°F to 90°F that way. Warm epoxy pumps and mixes better and wets out better. Warm the joint itself with a heat lamp or hair dryer, or tent just that area. Know your hardener's floor. WEST 205 Fast cures down to 40°F (4°C), but slowly. 206 Slow and 207 Special Clear shouldn't be used below 60°F (16°C), and 209 Extra Slow not below 70°F (21°C). As a rule, cure time doubles for every 18°F (10C) drop.
  6. Heat for the cure without combustion in the room. If you need heat while the epoxy cures, WEST says to avoid unvented open-flame heaters that burn kerosene or fuel oil. Unburned fuel can contaminate the surface, and the extra moisture and CO2 contribute to amine blush. Turn up the thermostat, or use electric heaters or electric blankets. CPSC says an electric heater should have a thermostat and a tip-over shutoff, and to avoid ordinary extension cords. If you do run a combustion heater at other times, follow its fresh-air rule. That DESA manual calls for at least a 3 square foot opening to outside air for each 100,000 Btu/hr.
  7. Change cartridges on a schedule and store them sealed. 3M says to write the date on the cartridges when you open them, change them on a schedule, and change them right away if you can smell or taste the solvent. Between uses, store the respirator and cartridges in a sealed bag or container, away from the vapor. Even sealed, vapor can migrate through a used cartridge overnight. 3M says that for chemicals boiling below 65°C, an OV cartridge shouldn't be used longer than one shift. Acetone boils at 133°F, which is 56C. So after an acetone day, those cartridges are done.
  8. Hang a CO alarm in the shop. CPSC says unvented fuel-burning heaters pose the greatest CO threat, and mild CO symptoms like drowsiness, headaches or nausea are often misdiagnosed. A battery CO alarm is cheap. CPSC says to test alarms monthly and replace the batteries every year.

MOAM's shop note: The mistake I see most is the guy who opens a window "for ventilation" and leaves the torpedo heater roaring right next to the boat while he wipes her down with acetone. That's the worst of everything: an ignition source, CO, and a blush factory, all in one corner. Here's the trick. Do your solvent work first thing, right after you've warmed the place up and shut the heater off. The shop holds its heat long enough for a wipe-down. Then purge, close up, and let the epoxy cure under electric heat or in a tent. And never clean epoxy off your hands with solvent. WEST says not to. Use a waterless skin cleanser, then soap and warm water.

MOAM Out.

Sources: WEST SYSTEM: Preventing Overexposure WEST SYSTEM: Epoxy Safety (PDF) · Epoxyworks: Cold Weather Bonding · Epoxyworks: Let's Talk About Amine Blush · Epoxyworks: Disposable Gloves · Fine Woodworking: The Finishing Environment (Jeff Jewitt) NIOSH Pocket Guide: Acetone · ICSC 0087: Acetone · NIOSH cartridge color chart (CDPR) · 3M 60921 OV/P100 cartridge 3M: Reuse of Organic Vapor Cartridges · 3M Respirator FAQs · OSHA 29 CFR 1910.134 (Appendix B-1 seal checks) · CPSC: Space Heater Safety · CPSC: CO Alarms · CPSC: Kerosene Heater Safety · DESA propane forced-air heater manual

New Real Estate Listings on the North Shore Today – Thursday, November 12

New Listings Today – North Shore 29 Towns

Morning, North Shore, the MOAM's been scrolling the new listings again….. 47 new listings hit the market over the last 24 hours, across 17 North Shore towns.

Top towns: Salisbury and Salem with 7 each, Peabody 6, Lynn 5, Newbury 4, and Marblehead and Amesbury with 3 each.

By property type: Residential 33 · Residential Lease (rentals) 10 · Residential Income 2 · Commercial Sale 1 · Land 1.

The MOAM's take: Salisbury and Salem tied for the lead today, and homes for sale made up most of the new inventory.

Contact Nanepashemet to view these.
Nanepashemet Real Estate Services
Call or text 781-727-6516
jnestor@nanepashemet.com

MOAM Out.

Listing data courtesy of MLS Property Information Network (MLS PIN); listings shown are held by various brokerages. Nanepashemet Real Estate Services, MA Broker Lic. 136995-RE-B.

Boston Sports Morning Report — Thursday, Nov. 12

Boston Sports Morning Report — Thursday, Nov. 12

Not for nuthin'…. But….. the Celtics gutted out a win in Toronto last night, and the B's have the Habs at the Garden tonight with first place in the Atlantic on the line. Here's your Thursday board.

New England Patriots

  • Yesterday: No game (lost 45-27 to Green Bay on Sunday)
  • Today: No game
  • Next: Sun., Nov. 15, 9:30 AM ET, @ Detroit Lions (in Munich, Germany; Fox)
  • Standings: 5-4, 2nd in the AFC East, 2.5 games behind Buffalo (7-1), currently the No. 7 seed in the AFC

Still holding the last AFC playoff spot. Shake off the Green Bay game and get ready for an early-morning kickoff overseas.

Boston Red Sox

  • Yesterday / Today: No games, it's the offseason
  • Next: Opening Day, Thu., March 25, 2027, @ Seattle Mariners (start time to be announced; home opener at Fenway is Thu., April 1 vs. Cincinnati)
  • Final 2026 record: 87-75, 3rd in the AL East, out in the Wild Card round vs. the Yankees

Hot stove season. Pitchers and catchers can't come soon enough.

Boston Celtics

  • Yesterday: Won 98-93 @ Toronto
  • Today: No game
  • Next: Sun., Nov. 15, 6:00 PM ET, vs. Dallas Mavericks (TD Garden)
  • Standings: 10-2, 1st in the Atlantic (1 game ahead of Philadelphia, 9-3), No. 1 seed in the East, 5-game winning streak

Not the prettiest one, but a win is a win, and that's five straight. Home for Dallas on Sunday.

Boston Bruins

  • Yesterday: No game (won 4-1 vs. Florida on Sunday)
  • Today: Tonight, 7:00 PM ET, vs. Montreal Canadiens (TD Garden, NESN)
  • Next: Sat., Nov. 14, 7:00 PM ET, vs. Minnesota Wild (TD Garden)
  • Standings: 13-4-1, 27 points, 1st in the Atlantic, No. 2 in the East; Tampa Bay and Montreal are each a point back (26)

Four straight wins and a crowded top of the Atlantic. The Garden should be rocking tonight.

That's the Thursday board. Enjoy the day, Boston.

MOAM Out.