This is catching the MOAM's attention today….. how hard to crank the clamps. Walk into any shop from Gloucester to the Cape and you'll see two kinds of glue-ups. One guy leans on every handle like he's trying to close a stuck storm door. The other guy gives it a polite little twist and hopes for the best. Both of them are guessing. You don't have to. The glue makers publish the numbers, and the math takes about a minute on the back of a scrap.
Why it matters: Clamp pressure squeezes the glue into a thin, continuous film, pulls the faces into full contact and holds everything still while it sets. Too little and the joint never closes. Way too much on a small glue area and you crush the wood and push the glue out. For yellow PVA glue, Titebond's own spec is "enough to bring joints tightly together," which works out to about 100 to 150 psi for softwoods, 125 to 175 psi for medium woods and 175 to 250 psi for hardwoods. The USDA Wood Handbook says the same thing in government-speak: about 100 psi for low-density wood, up to about 250 psi for the densest stuff.
Materials
- PVA wood glue (Titebond Original, II or III) for shop and interior work
- Epoxy, wood flour or other thickening filler for the boat (more on that below)
- Cauls and wax paper or packing tape so the cauls don't get glued on
- A damp rag or a scraper for the squeeze-out
Tools
- Enough clamps. Pipe clamps, parallel clamps, bar clamps, whatever you've got, but count them first
- Tape measure and a pencil for the math
- A couple of bench risers so you can clamp over and under the work
Steps
- Dry fit first. A good joint should close with light pressure. If you need a ton of force to pull a gap shut, fix the joint. Don't count on the clamps. PVA isn't a gap filler, and the Wood Handbook says most wood glues don't fill gaps well.
- Figure the glue-line area. That's the area of the faces getting glued, not the face of the board. Edge-gluing two 3/4-in. boards, 36 in. long: 3/4 × 36 = 27 sq in.
- Multiply by the psi for your wood. White pine at 100 to 150 psi needs 2,700 to 4,050 lb total. White oak at 175 to 250 psi needs 4,725 to 6,750 lb. That's a lot more than most folks think.
- Divide by what your clamps can do. A Pony #50 3/4-in. pipe clamp is rated at 1,200 lb. A BESSEY K Body REVO parallel clamp is rated at a nominal 1,700 lb, a BESSEY TGC clutch-style bar clamp up to 700 lb, and a BESSEY EZS one-hand clamp at a nominal 445 lb. So that oak joint wants 4 to 6 pipe clamps, 3 to 4 parallel clamps, or 11 to 16 of the one-handers. Those ratings are best case. When WOOD Magazine tested one-handed bar clamps, they only got into the softwood range or a bit under it. Treat your count as the minimum.
- Space them so the pressure overlaps. Fine Woodworking's rule of thumb is that clamp pressure spreads in about a 45° cone from each jaw, so it reaches along the glue line about as far as the jaw sits from it. Alternate clamps over and under so the panel doesn't bow. (Spacing and cauls got their own tips back in September and October.)
- Spread an even coat and clamp from the middle out. Bring each clamp up snug, then go back around. With big pipe and parallel clamps, snug is the word. You don't need to hang off the handle.
- Read the squeeze-out. What you want is a small, continuous bead along the whole joint. That tells you there's enough glue and the joint is closed. If the bead has dry skips, you're short on glue or the clamps are too far apart. That's your "starved" joint. If you see big puddles, you used too much glue, not too much pressure.
- Then hands off. Titebond says to keep an unstressed joint clamped 30 minutes to an hour, and 24 hours for a stressed joint. Don't put stress on it for 24 hours.
The "starved joint" business: Everybody's heard you can starve a joint by over-clamping. With PVA and hand clamps on a full-length edge joint, that's mostly a myth. Fine Woodworking tested it and found that tight joints didn't starve. The professor they worked with said most woodworkers actually under-clamp. Where it gets real is a big clamp on a small glue area. Put one 1,700-lb parallel clamp on a 3/4 × 2-in. joint (1.5 sq in) and you're over 1,100 psi, more than four times Titebond's top number. That's how you crush fibers and squeeze the glue away. WOOD Magazine's advice fits: with the heavy clamps, don't go past snug.
Epoxy plays by different rules. On the Chamberlain dory, anything below the waterline gets epoxy, not Titebond. Titebond III's own spec says it's not for continuous submersion or below the waterline. WEST SYSTEM's guidance is the opposite of "crank it." Use only enough clamping pressure to hold the parts in place and squeeze a small amount of thickened epoxy out of the joint. Don't squeeze it all out. That's how you get a resin-starved epoxy joint. Wet out both faces with plain mixed epoxy first, then put on epoxy thickened just enough to bridge any gaps. When you're bedding hardware, tighten the fasteners until epoxy squeezes out, and stop there.
MOAM's shop note: Do the math before the glue comes out, not after. If the numbers say you need eight clamps and you own five, you'll find out halfway through a ten-minute open time with glue on your elbows. Count them, lay them out, set them to width and dry-run the whole thing. And one for the boat shop: never treat epoxy like yellow glue. The guy who cranks a scarf or a stem lamination down until nothing comes out has just built himself a dry joint.
Snug, not strangled. Let the glue do the work.
MOAM Out.
Sources: Titebond Original, II, III and Speed Set technical data (titebond.com); Titebond FAQs; USDA Forest Products Laboratory, Wood Handbook, Chapter 10; Fine Woodworking, "How Strong Is Your Glue?" and the Roman Rabiej clamping series; WOOD Magazine, "Take it easy with clamping pressure"; Woodcraft, "Goof-Proof Clamping"; Pony Jorgensen pipe clamp fixture specs; BESSEY Woodworking Solutions 2023-2024; WEST SYSTEM User Manual and Handy Pack instructions.


No comments:
Post a Comment