Quick one from the dory shop tonight….. Ever had an oarlock socket work loose halfway across the harbor? A screw in plain wood holds by a few threads biting into fibers that swell, shrink and eventually let go. Every pull on the oar works it a little more. Water gets in around the threads and the wood around the hole goes soft. Next thing you know you're rowing home with one oar and a lot of opinions.
4 5Why it matters: Epoxy fixes that two ways. It soaks into the wood around the hole and stiffens it, which effectively makes the fastener bigger. And it seals the hole so water can't get to the end grain. Gougeon Brothers, the WEST System folks, lay out a few levels of this, from a quick wet-out of a pilot hole to fully bedded hardware. On the Chamberlain Marblehead gunning dory, the high-load stuff gets the full treatment: oarlock sockets, the bow eye, cleats, anything somebody will yank on. It works just as well on the GC side, for a railing post base or a gate hinge on a wet deck.
6 7Materials:
8-
9
- Epoxy resin and hardener, metered right (pumps or a scale) 10
- High-density filler (WEST 404 is their first choice) or colloidal silica (406) 11
- Silicon bronze or stainless fasteners and the hardware 12
- Pipe cleaners, a plastic syringe, mixing cups and sticks 13
- 50-grit sandpaper, acetone or alcohol for cleanup, masking tape 14
- Paste wax, only if you'll ever want the screw back out 15
Tools: drill, a pilot bit sized for your screw, a bigger bit for the oversize hole, a depth stop or a flag of tape on each bit, screwdriver, nitrile gloves.
18 19The steps:
20 21-
22
- Mark the hardware and dry-fit it. Set the hardware in place and mark the holes. Drive the screws once dry so you know everything lines up. Then take it all apart. 23
- Drill the oversize hole. WEST says to go 2/3 to 3/4 of the fastener's depth, at up to twice the screw's diameter. For a #10 x 1-1/2 in. screw (about 0.19 in. across the threads), that's a 3/8 in. hole about 1 in. deep. Put a tape flag on the bit so every hole comes out the same. 24
- Drill a normal pilot at the bottom to the full length of the screw. This is the part people skip. Those last threads in fresh wood are what hold the hardware tight while the epoxy cures. If you can clamp the hardware some other way, you can run the oversize hole the full depth. 25
- Wet it out. Mix a small batch of plain epoxy. Work it into the hole with a pipe cleaner or syringe and coat the screw threads. Give it a few minutes to soak into the end grain. Top it up if it disappears. 26
- Prep the hardware base. Clean the metal, coat the bottom with plain epoxy, then sand it in with 50-grit while it's wet. Sanding through the wet epoxy puts it right onto fresh metal before that metal can oxidize. 27
- Thicken and fill. Stir 404 or 406 into the rest of the batch until it won't sag, about like peanut butter. Inject it into the hole from the bottom up so you don't trap air. Butter the threads and the bottom of the hardware too. 28
- Set the hardware. Drive the screws just until a small bead squeezes out all around. Snug, not cranked. Squeeze too hard and you push the epoxy out of the joint. 29
- Clean up the squeeze-out. Tool it into a small fillet with a rounded stick, or wipe it off. Do it now while it's soft, not tomorrow with a chisel. 30
- Let it cure. WEST says at least 24 hours before you load the hardware, and more in cold weather. In a Marblehead shop in November, I give it a couple of days, or put a little heat on it. 31
Three levels, pick by load:
34-
35
- Light duty: wet out a standard pilot hole with plain epoxy and drive the screw. 36
- Stripped hole: wet it out, add a second coat thickened, then drive the screw into it. 37
- High load: the full oversize-and-fill method above, with the hardware base bedded in epoxy. 38
MOAM's shop note: Think about tomorrow before you bond something today. If there's any chance that fitting has to come off, wipe the screw threads with paste wax first. WEST says it contaminates the surface enough to keep the epoxy from bonding to the screw, and you still get the sealed, reinforced hole. Already bonded one you need out? Heat the screw head with a soldering iron (or carefully with a torch, behind a heat shield). At about 120°F the epoxy softens enough to back the screw out. Give long or fat screws more time for the heat to travel down.
41 42Sources: WEST System, Bonding Fasteners and Hardware (wetting out pilot holes, oversize holes 2/3 to 3/4 of fastener depth and up to twice the diameter, full-length pilot, 404 preferred or 406, 50-grit sanding of the base, 24-hour minimum cure, wax for removable fasteners, heat to about 120°F for removal); WEST System, User Manual and Product Guide (same sequence, why sanding into wet epoxy matters on metal); ATL Composites, Bonding Fasteners and Hardware (summary of the same numbers); ASME B18.6.1 wood screw dimensions (#10 screw is 0.190 in. nominal).
43 44MOAM Out.


No comments:
Post a Comment